diy

To mark the occasion of 10,000 downloads of parts from the previous four sets, I’ve made a fifth set of Fritzing parts. The first set of parts, along with some details about Fritzing and about part creation, can be found here. All sets can be found under the ‘fritzing’ tag here. As with the previous sets, these are generally parts that I’ve needed for my own projects.

The group of Fritzing parts.

The group of Fritzing parts, numbered.

The parts are as follows:

1. YL-83 Rain Sensor (Control Board | Detection Board)
2. SIM800L GSM/GPRS Module
3. LIDAR-Lite v2
4. ACS712 Current Sensor Module
5. Breadboard (25 pin)
6. BMP280 Breakout Board
7. BH1750 Breakout Board (GY-302)
8. 2-Channel 5V Power Relay Module
9. HB-100 Microwave Sensor Module
10. 4-Channel 5V Power Relay Module

Since the Fritzing parts repository (code.google.com/p/fritzing/issues/detail?id=2753) is no longer available for sharing parts, they will be posted here instead.   If you’d like to make a request for the next set, please leave the following details in the comment section below:

1. The name of the board/module
2. The outside dimensions in millimeters
3. Details about each pin (i.e. name — e.g. VCC, GND, SDA)
4. An image of it at a reasonable resolution (and as close to parallel to the image plane as possible)

This is the fourth set of Fritzing parts that I’ve made. The first set of parts, along with details about Fritzing and about part creation, can be found here. All sets can be found under the ‘fritzing’ tag here. As with the previous sets, these are generally parts that I’ve needed for my own projects.

The group of Fritzing parts.

The group of Fritzing parts, numbered.

The parts are as follows:

1. 5V 1 Channel Power Relay
2. Piezo Element
3. HRXL-MaxSonar-WR Ultrasonic Range Finder
4. FT232RL USB to Serial Breakout
5. TTP223B Capacitive Touch Sensor
6. QRE1113 IR Reflectance Sensor Breakout
7. LilyPad Reed Switch
8. GT-511C1R Fingerprint Scanner
9. YwRobot Breadboard Power Supply MB-V2 (3V3 & 5V | 5V & 5V | 3V3 & 3V3)
10. Arduino WiFi Shield

Since the Fritzing parts repository (code.google.com/p/fritzing/issues/detail?id=2753) is no longer available for sharing parts, they will be posted here instead.

If you’d like to make a request for the next set, please leave the following details in the comment section below:

1. The name of the board/module
2. The outside dimensions in millimeters
3. Details about each pin (i.e. name — e.g. VCC, GND, SDA)
4. An image of it at a reasonable resolution (and as close to parallel to the image plane as possible)

This is the third set of Fritzing parts that I’ve made. The first set of parts, along with details about Fritzing and about part creation, can be found here. The second set can be found here. As with the previous two sets, these are generally parts that I’ve needed for my own projects.

The group of Fritzing parts.

The group of Fritzing parts, numbered.

The parts are as follows:

1. HC-SR04 Ultrasonic Distance Sensor
2. 60 x 90 mm Solar Panel
3. Water Level Sensor
4. DSN-DVM-368L Digital Voltmeter
5. MPS20N0040D-D Sphygmomanometer
6. NeoPixel V2
7. I2C Logic Level Converter Module
8. MQ-3 Breakout Board
9. Barrel Power Connectors
10. ZE-4F180 Water Solenoid

Detail of the NeoPixel v2.

The parts will be released via the Fritzing parts repository (code.google.com/p/fritzing/issues/detail?id=2753). Links will be added to the list above.

If you’d like to make a request for the next set, please leave the following details in the comment section below:

1. The name of the board/module
2. The outside dimensions in millimeters
3. Details about each pin (i.e. name — e.g. VCC, GND, SDA)
4. An image of it at a reasonable resolution (as close to parallel to the image plane as possible)